BSD 2-SPEED RC Nitro Powered car Monster 4×4 Truck 1:8

7Sep/090

BSD 2-SPEED RC Nitro Powered car Monster 4×4 Truck 1:8

3632204774838280 BSD 2 SPEED RC Nitro Powered car Monster 4x4 Truck 1:8 nitro rc car

1/8 Scale Ready To Run Nitro Powered Monster Truck Retail: $1099! Capable Speed up to 80km/h (The colour of car black or white will be picked as random choice) Bsd racing monster truck with new upgrades! Great truck for racing or offroad very fast with a 21# SH motor 3.5 horsepower. Auto-shifting 2-speed transmission. great truck for racing or offroad can handle the most craziest terrain! Race ready chassis! Includes 2 Channel pistol grip transmitter! required: AA batteries, glow igniter SPECFICATIONS Length : 504 mm Width : 385mm Height :208mm Wheelbase :335 mm Ground clearance :46mm Tire Size 145*71mm Engine:SH21# 3.5 horsepower FEATURES 1)4WD drive system. 2)21CXP Engine, improving the car's motivity. 3)Waterproof and dustproof sealed gearbox. 4)Auto-shifting 2-speed transmission. 5)Sealed superduty plastic driveshaft. 6)Fast easy assembly and disassembly of receiver and battery cover. 7)Super diff with four bevel gears. 8)Blue anodised 6061T chassis. 9) Adjustable alloy shock absorbers. 10)Tuned Chrome exhaust 11)Enclosed Pod air filter WE STOCK ALL BSD RACING PARTS AND UPGRADE PARTS!!! Technical Introduction BREAK IN PROCEDURE Before running the engine,read the manual and watch the assembly. STARTING THE ENGINE IMPORTANT! Your radio system must ALWAYS be turned on and the transmitter ansmitter antenna fully extended when running the engine! 1.Fill the fuel tank. 2.Prime the engine-while the engine is cool,place your finger over the tuned pipe's exhaust hole and pull the recoil gently several times.Do not over-prime!Stop when you see fuel in the fuel line at the carb. 3.Install a glow starter(B7004C) into the glow starter ans attach the starter to the glow plug. 4.With the throttle at idle,start the engine by pulling the recoil using short,quick pulls.DO NOT pull the recoil starter's string to the end.You only need 10 to 12 inches of pull to start the engine with the throttle at idle. Sometimes it is helpful to start the engine at around half throttle.When the engine starts,immediately return the throttle to idle.If this is not done the engine can over-rev and cause engine damage. IMPORTANT! FIXING A FLOODED ENGINE If the engine id difficult to turn over with the recoil starter,especially if it is brand new,loosen the glow plow plug a hagf turn before starting the engine.This allows some compression to escape,but the engine will still start.Make sure you tighten difficult to pull,the engine is flooded-there is too much fuel inside the engine.Remove the glow plug,then turn the buggy upside down and pull the recoil 5 or 6 times.This will clear the engine of fuel,and you will notice the recoil pulls easier.Rep;ace the glow plug and repeat the starting procedure. STOPPING THE ENGINE Pinch the fuel line that runs to the carburetor.Pinching this line will restrict the fuel flow and the engine will quit within a few seconds.Never place your finger over the exhaust to stop the engine.This could result in serious in serious burns on your finger.It also causes fuel to back up in the engine,making it harder to start the next time you run your car. BREAK IN PROCEDURE Some things to remember during break-in 1.Run with the body off.This will keep the engine cooler. 2.Keeo the air cleaner on at ALL times. 3.Run on a smooth,hard surface.An empty parking lot is perfect. 4.Use the same fuel that you will use for normal running. 5.Resist the urge to accelerate and decelerate quickly. 6.Break-in puts stress on the glow plug and can burn it out.Make sure you have an extra plug or two on hand. 7.Do NOT overheat the engine. TANK 1 Your first tank of fuel should be running the car at a very rich needle valve setting.This allows the fuel to carry as much oil as possible into the engine to properly lubricate the internal parts during the break-in. 1.Open the high speed needle valve 4-1/2 turns from fully closed(counterclockwise).This is factouy set already,but check it to make sure.When closing the high-speed needle,close until youfeel some resistance.DO NOT overtighten or you will damage the engine. 2.Fill the fuel tank and start the engine. 3.Run the buggy on a smooth surface with the body off. 4.Run back and forth at medium speeds,slowly accelerating and decelerating the buggy. 5.Run the buggy until the tank is almost out of fuel.Do not allow the tank to run out of fuel during break-in.This leans out the engine and can cause overheating. 6.Stop the engine and allow it to cool.This noumally takes around 10-15 minutes. NOTE:If your engine does not stay running consistently,increase the idle speed by turning the idle stop screw clockwise. TANK 2 Lean the high-speed needle 1/12 turn from "tank 1" setting.Run the buggy for the complete tank and then let cool. TANK 3 Lean the high-speed needle another 1/12 turn from "tank 2" setting.Run the buggy for the complete tank and then let cool. TANK 4 Lean the high-speed needle another 1/12 turn from "tank 3" setting.Run the buggy for the complete tank and then let cool.You should notice the engine running much better at this point. TANK 5 Lean the high-speed needle another 1/12 turn from "tank 4" setting.Run the buggy for the complete tank and then let cool.The engine is now ready to be perfoumanced tuned. Important! At this point,the engine will likely be running at a faster idle speed than needed (This is typical after break-in).Adjust the idle stop screw to lower the idle speed so that the wheels do not ,or just barely,rotate when you lift the buggy off 2-CHANNEL TRANSMITTER SYSTEM: The servo must be set at the center position befor installation,to set the neutral turn on the transmitter and receiver,set the trim tabs in the center position,and turn off the receiver and transmitter in succession,the servo will be in the proper neutral position for installation Return Police Please choose carefully,We do not give refunds on this item. If the goods are found to have a manufacturing defective we will send out the replacement parts needed for the repair, Or the buyer are able to return for repairs ( return postage cost to be at buyers expense). The buyer has 7 days from the date of invoice to contact us if the item is fund to have defective. We reserve the right to refuse any claim made after this time frame or additional charges (postage & handling) may apply. The user is required to carefully read the instruction manual provided above and to follow those guidelines prior to starting the vechile. Please note that once the engine has been started anything after that point is not considered as manufacturers defect. We accept no responsibility for crash damage or the improper installation of parts. If you are uncertain as to your ability to be able to operate a model, please discuss with us BEFORE YOU MAKE THE PURCHASE, so that we can best assist in advising the model suitable for you. We offer free technical support with all our RC models via telephone or in our shop.